在线咨询
扫一扫

官方微信二维码
扫描加关注

全国免费服务热线
18560211715

返回顶部
新闻动态主页 > 新闻动态

对澳门新莆京娱乐网站抗倍特板材使用的加工步骤

1澳门新莆京娱乐网站抗倍特板开料时,应以直线锯切为主。通常可先在这种板材上画好规格尺寸,然后再锯切,如果工件的尺寸为标准尺寸,可先用模板划线,再进行锯切,这会方便得多。
1 fomica compact panel cutting, should be in a straight line cutting. Usually first in the plate to draw a good size, and then saw cut, if the size of the workpiece as the standard size, you can use the template line, and then cut, it will be much more convenient.
2.开孔时,可利用手提曲线锯进行切割,切割速度以3-4m/min为宜,如切割速度过快,一方面会使切割边缘产生爆口等缺陷,另一方面也会影响锯条的使用寿命,增加加工成本。
2. Opening, using portable curve saw is used for cutting, the cutting speed to 3-4m/min is appropriate, such as the cutting speed is too fast, on the one hand will explode mouth defects such as cutting edge produces the, on the other hand will the service life of the saw blade, increase the cost of production.
3.加工异形边沿时,应先在板件表面划出所需尺寸,然后利用曲线锯切割;如果批量生产时,可利用模板进行切割,这样可确保加工速度和锯切质量。
3 when processing special shaped edge, should first draw the required size on the surface of the plate, and then use the curve saw cutting; if the mass production, the template can be used to cut, so as to ensure the processing speed and cutting quality.
澳门新莆京娱乐网站
4.加工边缘时,普遍采用的工具是手提镂铣机,在作业前,应清除板件表面的灰尘或异物。
4 processing edge, commonly used tool is portable router, in front of the work, should be cleared of plate surface dust or foreign matter.
5.砂磨时,按顺序分别采用80#、220#和320#砂纸对边缘进行砂磨,打磨速度以15-20分钟打磨2.5米长度为基准;打磨时,应注意不要损坏表面装饰层,打磨结束后,用抛光剂对边缘进行抛光处理。
5. Sand grinding, sequentially respectively by No. 80, No. 220 and 320 grit SiC paper, edge grinding, grinding speed to 15-20 minutes grinding 2.5 meters in length as the benchmark; polished, care should be taken not to damage the surface decorative layer, grinding the end, polishing agent, polishing treatment is carried out on the edge.
6.如要利用螺钉连接产品,应先用比螺钉直径小的钻头钻一个小孔,然后向小孔注入粘合剂,再把螺钉拧入,并保证螺钉牙纹的上沿部分拧入5mm以上。
6 if you want to use screws to connect the product, should be used to drill a small hole than the diameter of the screw, and then to the hole into the adhesive, and then screw into the screw, and ensure that the screw thread on the upper edge of the screw into the 5mm.
7.钻杯状暗较链孔肘,板件的剩余厚度至少保留3mm以上,如剩余厚度过薄,杯状绞链埋入后,会发生破损或出现凸痕。
7 the residual thickness of the plate is more than 3mm, and the residual thickness of the plate is more than that of the chain, and the residual thickness is too thin.
8.安装结束时,如澳门新莆京娱乐网站抗倍特表面出现斑点或污迹,可用毛巾沾取少量油性清洁剂(油与丙酮的混合物)轻轻擦拭这些斑点或污点
Installation 8. At the end, such as Formica anti Beite surface spots or stains, towels available dip take a small amount of oil cleaning agent (a mixture of oil and acetone) gently wipe the spots or stains

<<
Baidu
sogou
>>